The inlet oil is filled in the rotating gear groove and extruded along the inner surface of the casing to the outside of the gear.
The oil between the output side and the suction side can only be discharged when the two gears are meshed. The output pressure is set at 5.2kpa, and the compressed oil is delivered to the main pump and pilot circuit.
1. Structure and principle of rotary motor assembly
(1) structure of rotary motor assembly
The rotary motor assembly includes a valve cover part, a rotary motor part and a rotary reduction gear part. The valve cover part includes rotary parking brake, crossover valve and auxiliary valve. The structure of the rotary motor assembly is shown in Fig. 2-42.
The rotary motor is a swashplate axial piston motor. The rotary motor is composed of swash plate, hydraulic cylinder group, piston with intermediate bush, valve plate, parking brake and motor shell.
Each piston is equipped with brake shoe, and nine pistons with brake shoe are inserted into the hydraulic cylinder. Nine pistons are supported by the swash plate and slide on the viewing surface of the swash plate. The hydraulic pressure makes the piston move in a straight line in the hydraulic cylinder group, and produces a rotating force to make the hydraulic cylinder rotate.
Since the hydraulic cylinder group is connected to the output shaft with a needle, the rotating force of the hydraulic cylinder group is transmitted to the output shaft. The rotation force of the output shaft is transmitted to each rotating gear through the rotating reduction gear.
(2) working principle of rotary motor
The casing part includes the air defense valve and cross valve. The high pressure oil enters the rotary motor through port a or port B in the direction of rotation. The oil path of high pressure port and low pressure port of rotary motor is shown in Fig. 2-43.
Each piston is connected to the sliding block by ball or sleeve joint. When the oil is squeezed into the top of the piston, the slider slides around the thrust plate, causing the motor to rotate. The shield is fixed against the plate by spring force. The oil flows into or out of the piston through the fixed valve plate.
Rotary motor is a fixed displacement motor, its rotation speed is increased or decreased according to the amount of oil delivered to the rotary motor.
Source: Jiangmen construction machinery accessories manufacturer http://www.hx-machinery.cn/
12-17
Working principle of gear pump brake valve
(1) when the valve control lever is neutral, the oil pressure at port P is equal to that at port R. When the oil pressure of port P increases, the pressure area of plunger, the pressure of port P, the elasticity of tension spring and the pressure of chamber G are balanced, so the valve starts to operate. When the piston moves, the pressure of chamber g changes, so the safety pressure is affected by the tension spring and piston. Because the piston moves, the safety pressure increases from P1 to
12-17
Methods of waterproof scale for gear fittings of excavator
We should all have seen excavators, so do you know how to prevent the scale of excavator accessories? Today, we specially invited modern excavator accessories manufacturers to tell us the methods of modern excavator accessories anti scaling. Let's follow Xiaobian to have a look! (1) magnetize the water quality. Some small magnets are placed in the engine structure system. The magnetic field generated by these magnets magnetizes the cooling water. The magnetized water can reduce the scale composi
12-17
How to maintain gear parts of Jiangmen excavator?
The rotary table of excavator accessories plays an important role in the daily work, because the bad working environment or improper operation of the excavator will cause a series of failures of the rotary table, such as wear aggravation, abnormal noise, oil seal replacement and so on. When encountering these problems, first of all, open the cover plate around the boom mounting base, and investigate the amount of grease in the big gear ring and the wear condition of the gear ring. Because of the
12-17
How to change gear oil for rotary motor reducer?
Oil change time: after the oil change cycle is reached, the new gear oil must be replaced. After the excavator stops working for half an hour, the gear oil is at the bottom of the reducer, and the oil temperature is not too high or too low. The old oil can be drained as much as possible. After the old oil is drained, tighten the oil drain screw, and then add new gear oil from the gear oil filling port. Pay attention to the adjustment at this moment Check the travel scale to avoid too little or t